Tee for connecting the washing machine to the water supply

Tee tap for connecting a washing machine

Having bought a new washing machine or moved to another apartment, you will have to connect it to communications. Even if there are no conclusions, then they can be mounted independently, without resorting to the help of a plumber. After arranging the conclusions, additional details will be needed. So, in order to "power" the device to the water supply, you will definitely have to buy a special tee tap. Let's look at the types of devices and their features.

Types of taps for washing machines

Equipment can be connected to the water supply in two ways: a separate branch pipe or through a tie-in into a pipe (for example, going to a water tank or sink). A tap for connecting a washing machine can be of two main types:

  • tees or bushings (if you have to cut directly into the pipeline);
  • corner, when there is a separate branch for connecting a washing machine.

Note. Instead of angle valves, you can use a regular water ball valve or a fitting - it all depends on the situation.

Regardless of the type, all cranes are divided into:

Their difference is only in the method of blocking water, no other design features .

What is the best faucet to install?

The installation method and the choice of parts are more dependent on financial capabilities and skills than on the location of the machine. To use a valve, through passage or ball type of valve is a matter of budget. Let's see how the details work in practice.

Using a globe valve


This method is the most acceptable, since it is simple and economical, does not require special devices for connecting pipes or threading. The through valve can be installed on the water supply hose, for example, connect it to:

  • washbasin;
  • faucet in the kitchen
  • drain tank hose;
  • water heating tank.

When choosing a through valve, it is important to choose the correct direction of the lever (valve) itself. If it rests against a wall or is in a hard-to-reach place, it will be problematic to turn off the water.

To connect a tee, it is enough to have a set of keys, a gas key and a FUM tape in stock. Also remember a few useful installation rules:

  1. The tee can be installed both before and after the hose on the drain tank.
  2. When connecting to a mixer, do not install a tee to old pipes.
  3. Use the “supply” (supplies water to the tank) pipe on the water tank to install the tap, otherwise the machine will draw hot water from the tank.

The installation process of the tee is quite simple:

  • first, unscrew the locknut and coupling on the hose (this can be done with both a regular key and a gas one);
  • remove all the old FUM tape from the thread and wipe it;
  • if the pipe is old and metal, then clean its end well with a file so that the surface is even (this is not necessary for plastic pipes);
  • wind the FUM tape onto the pipe and install the tee;
  • screw the FUM tape onto the outer thread of the tee and screw the hose from the drain tank / faucet / water tank, and into the remaining hole the hose from the washing machine.
  • tighten the connections with a gas wrench.

Please note that most cheap hoses cannot be used a second time, as the sealing gum becomes hard and does not return to its original position. Therefore, it begins to pass water. Better stock up on new hoses.

Application of angle taps


Unlike tees, this type of valve has only two outlets. Cranes are used to connect the washing machine hose to the pipeline, where a separate pipe is allocated for the washer. The method of connection with an angle valve is easier and more reliable than a tee, but it is more expensive - you will have to buy a special tee and an extra pipe. make a tie-in into the pipeline, install a tee there, then solder it and only then install the valve.

The process of installing a corner device is not much different from installing a tee:

  • prepare FUM tape, gas key and a set of ordinary keys;
  • wind the tape around the tap thread (on all threaded ends), then screw the valve into the pipe first, then screw the hose from the device to it;
  • check the connection for leaks.

There are a lot of models of this type of crane. The choice comes down to cost and design. It is better to take brass options.

Alternative

A tee fitting can also be used as a tee. To install it, you need to cut the pipeline, then install the fitting, after which you need to install a pipe going to the washing machine in the remaining hole. This method is very cheap and easy to perform, but not very reliable, since over time the sealing gum on the fitting deteriorates, and water begins to seep out. Instead of a washer faucet, you can use a regular ball valve. In terms of reliability, it is not inferior to a specialized one, but it costs much less.

Important! For connection to the pipeline, all taps use a half-inch female thread, a 3/4-inch outer thread for a washing machine, and a half-inch outer thread for plumbing. But in angle taps, both threads are external.

Examples of using


In theory, everything sounds simple, let's consider successful and “working” examples in practice.

Three-way valve from Fornara

This faucet is made in Italy. It belongs to the category of tees, therefore it has three threads: for a washing machine, plumbing and plumbing. The product is well made and lasts a long time. .

Croatian tees

Such three-way ball type valves are made of brass and coated with chrome plating. They have standard thread sizes and three outlets. The product has been in operation for at least 20 years.

Decorative corner faucet Rubinetta

As an angle valve, this mini model, designed specifically for washing machines, will look good. The crane is tiny, through passage, with a high-quality chromeplating.

Corner tap ITAP

This ball angle valve has the same thread on both sides - male half-inch. Used to connect any plumbing. not only washing machines. Made of brass, nickel plated.

Verdict

You can connect the washer in different ways. Which one to choose is up to you. The most reliable, but more expensive - through a separate pipe and an angle valve, a simplified version - using tees. Connecting the device directly is very undesirable, since to disconnect the machine from communication, you will have to completely shut off the water.

http://2stiralki.ru

Loading...
Top